For timer settings, see page When you select the Component name, go to Step 6. When you select the system number or the timer program number, go to Step 7. Press the TIME key. You can select the desired component and turn it on by just pressing that Component Select button or a Label key.
Page 45 Press the PowerON key. The display of the component names preset by Sony for which you can program the Power-on signal flashes. The display of the other components stays lit. Select the desired component by pressing the Component Select button or the Label key. And the keys for VCR appears. If you release the button before you hear a beep, the signal may not be learned correctly.
Page Notes On Learning The Signals Of An Air-Conditioner Notes on learning the signals of an air-conditioner About seasonal adjustments If you change the settings of the air- conditioner for the season, you have to program the remote control signals of the new settings on the Commander.
Press and hold down the button on the other remote control until you hear a beep. Press the X key. Page 58 Label key on this Commander the settings and learned signals programmed on the keys and buttons can be transferred to a Component Select button or key on another Sony RM-AV Follow Steps 1 to 6 on page To receive all the data from another remote commander Follow Steps 1 to 5 on page Page 61 Press the Component Select button to which you want to assign the data.
Or press the Label key to which you want to assign the data. The selected component name appears on the left Label key. And you can program the Key Macro function for the macro keys when the selected component name is displayed on the Mode Display key in Step 4, page Page 63 Select the component by pressing the Component Select button or the Label key.
The selected component name appears on the Mode Display key. The macro keys flash. If you select the component name for which the Key Macro function cannot be programmed Press the DAY key, and set the timer-on day s of the week by pressing the button. Each time the button is pressed the display of day s of the week changes as follows.
Set the timer-on hour by pressing the button. Then press the button so that the minute flashes. You can switch the mode between the hour setting and the minute setting by pressing the button. Set the minute by pressing the button. Press the COPY key. With a beep sound, the Timer Macro setting is cleared, and the Commander enters the Timer Macro setting mode Step 7 on page If you press the NG key The display returns to Step 5.
Note You cannot change the Timer Macro setting partially. Page 71 Select the program number of which timer standby mode you want to switch to on by pressing the Label key. If you create an Alias Component key, function keys Alias function keys that have the same function as the function keys in the Page 75 Press the key you want to set.
Press the component button to be referred to. Press the key you want to be referred to. Note You cannot select an already set alias key. Repeat Steps 5 and 7 to create other alias keys. However, the timer functions while the controls are locked. Then all the display contents are turned off.
To change this setting, perform the following procedure. You can adjust from 1 minute to 30 minutes. Each time the — key is pressed, the minute decreases by one. The display becomes in the setting mode of the Automatic-Off time of the backlight. The display returns to Step 3. You can adjust from level 1 to You can turn on or off the key- touch confirmation beep. Press the component select button or the Label key of which the name you want to change.
Follow Steps 2 - 5, on page Page 87 Follow Steps 1 - 4 on page Select the component name whose interval you want to change by pressing the Component Select button or the Label key. Press the KEY key. The keys of the selected component appear as set at the factory. LCD Touchscreen. Preset Code Database. Learning Infrared.
Advanced Programming. A Final Conclusion. Another Conclusion. Programming 1. Programming 2. Programming 3. User Reviews. Message Forum. Setup Menu.
Choose the component you would like to configure. Enter in the four-digit code number on the keypad corresponding to your brand and device.
To change the type of component, merely enter in a new four-digit number. Component types are changed automatically with the code number. If you pressed [Other], begin by selecting the component you would like to customize.
Then, select the key you want to teach a signal on. The remote will begin looking for an infrared signal to learn. Buttons cannot be relabelled if they already contain a learned signal, and cannot be customized for keys with preprogrammed codes. You cannot learn to a button that already contains a macro. To learn a single signal to a System Control button, press the desired System Control button.
To hide buttons from view, press [DEL] and the button you want to hide. Repeat until it flashes every other time. Buttons that flash every time contain a preprogrammed signal.
Buttons that are solid and do not flash contain a learned signal. To reset all learned and aliased buttons in a device, hold the [DEL] key and press the component name at the top of the screen. This will also reset preprogrammed buttons back to their original labels.
0コメント